UCDS Forum

Denis27 писал(а):other questen

which part i must choose when i will the Speedometer activate in the middle (the digital) of rpm and speed?
i dont find it

phpixde писал(а):

Denis27 писал(а):other questen

which part i must choose when i will the Speedometer activate in the middle (the digital) of rpm and speed?
i dont find it

Ist in IPC (High Lvl) => 10 DE06 ... => Digital Speedometer Feature (14)

Denis27 писал(а):with the new version it runs perfect. without the SEED KEY error. perfect work

peterpro писал(а):

Denis27 писал(а):with the new version it runs perfect. without the SEED KEY error. perfect work

Hi Denis, Dan, Dragunov or someone else!
So is there a final optimized step by step procedure to simple upgrade Mondeo 5 Euro IPC high level to the newest calibration? (For me from GS7T-14C026-BJA to actual BJE)
It's better to use VBF loader instead of Update wizard?
Better options in UCDS are "force all modules to sleep" and maybe "canbus logging" enabled? all others leaved disabled?
Due to the huge amount of time that seem it's needed to flash IPC (I've read 40 min.), it's naturally better to use a charger with virtual battery supply enabled to prevent on-board battery discharge and abnormal interruption of flashing process, but.......is there some tips to prevent some sleep of car with accessory powered on for 40 minutes? Leave the driving door opened? or something else?

Denis, did you update to latest BJE firmware successful with latest UCDS 2.0.002.002 trough VBF loader?

Thanks to all that can give some detailed information (even considering that updates are always dangerous)
Peter

peterpro писал(а):

Denis27 писал(а):with the new version it runs perfect. without the SEED KEY error. perfect work

Hi Denis, Dan, Dragunov or someone else!
So is there a final optimized step by step procedure to simple upgrade Mondeo 5 Euro IPC high level to the newest calibration? (For me from GS7T-14C026-BJA to actual BJE)
It's better to use VBF loader instead of Update wizard?
Better options in UCDS are "force all modules to sleep" and maybe "canbus logging" enabled? all others leaved disabled?
Due to the huge amount of time that seem it's needed to flash IPC (I've read 40 min.), it's naturally better to use a charger with virtual battery supply enabled to prevent on-board battery discharge and abnormal interruption of flashing process, but.......is there some tips to prevent some sleep of car with accessory powered on for 40 minutes? Leave the driving door opened? or something else?

Denis, did you update to latest BJE firmware successful with latest UCDS 2.0.002.002 trough VBF loader?

Thanks to all that can give some detailed information (even considering that updates are always dangerous)
Peter

dragunov писал(а):Why not use the VBF loader Dan?

Those are pure, using the Update Wizard can contain other VIN codes in it, no?

Hi Denis, Dan, Dragunov or someone else!
So is there a final optimized step by step procedure to simple upgrade Mondeo 5 Euro IPC high level to the newest calibration? (For me from GS7T-14C026-BJA to actual BJE)
It's better to use VBF loader instead of Update wizard?
Better options in UCDS are "force all modules to sleep" and maybe "canbus logging" enabled? all others leaved disabled?
Due to the huge amount of time that seem it's needed to flash IPC (I've read 40 min.), it's naturally better to use a charger with virtual battery supply enabled to prevent on-board battery discharge and abnormal interruption of flashing process, but.......is there some tips to prevent some sleep of car with accessory powered on for 40 minutes? Leave the driving door opened? or something else?

Denis, did you update to latest BJE firmware successful with latest UCDS 2.0.002.002 trough VBF loader?

Thanks to all that can give some detailed information (even considering that updates are always dangerous)
Peter

Dan wrote:
i would use the update wizard...select Mondeo (Euro) and update the JPC through there. Use the sleep all modules mode... Also make sure your headlights are off and auto wipers are off if you have them before starting. If not, they like to turn on during programming. Usually takes about 15 Minutes, not 40.... Scan and Clear DTCs when flashing is complete.

peterpro писал(а):

Hi Denis, Dan, Dragunov or someone else!
So is there a final optimized step by step procedure to simple upgrade Mondeo 5 Euro IPC high level to the newest calibration? (For me from GS7T-14C026-BJA to actual BJE)
It's better to use VBF loader instead of Update wizard?
Better options in UCDS are "force all modules to sleep" and maybe "canbus logging" enabled? all others leaved disabled?
Due to the huge amount of time that seem it's needed to flash IPC (I've read 40 min.), it's naturally better to use a charger with virtual battery supply enabled to prevent on-board battery discharge and abnormal interruption of flashing process, but.......is there some tips to prevent some sleep of car with accessory powered on for 40 minutes? Leave the driving door opened? or something else?

Denis, did you update to latest BJE firmware successful with latest UCDS 2.0.002.002 trough VBF loader?

Thanks to all that can give some detailed information (even considering that updates are always dangerous)
Peter

Dan wrote:
i would use the update wizard...select Mondeo (Euro) and update the JPC through there. Use the sleep all modules mode... Also make sure your headlights are off and auto wipers are off if you have them before starting. If not, they like to turn on during programming. Usually takes about 15 Minutes, not 40.... Scan and Clear DTCs when flashing is complete.

Thanks a lot Dan, for the tips....even if only 15 min i prefer to attach my charger with virtual battery mode that give to the car a constant 13,5 volt and a maximum of 15 amps, just to be sure that nothing could abnormally terminate the flashing procedure.
Did you find a solution for your parking aid?
Peter

dragunov писал(а):A friend of me keeps his car running during the update!

I guess none of the current files are meant to be on our cars, that's why we use VBF loader, no?

Cause u force-flashed the files yourself on your Mondeo IPC...